Fire CDC · Systems

CDC Fire Services for Class 2–9 Buildings

A practical overview of fire services that may affect NSW CDC projects in Class 2–9 buildings, from hydrants and sprinklers to smoke control.

Modern multi-storey Class 2 to 9 building requiring coordinated fire and life-safety systems

Class 2–9 buildings include apartments, accommodation, offices, shops, car parks, storage, factories, health-care and assembly buildings. Their fire strategies vary widely, so the first design output should be a project-specific requirements matrix rather than a copied equipment list.

Inputs that drive the fire scope

The project team should confirm:

  • NCC classification for every part;
  • current and proposed use;
  • floor area, volume and fire-compartment size;
  • rise in storeys and effective height;
  • type of construction and fire-resistance requirements;
  • occupant numbers, familiarity, mobility and sleeping risk;
  • storage commodity, height and special hazards;
  • fire-brigade access and site configuration;
  • available water supply; and
  • existing systems and fire safety schedule.

These inputs determine which NCC provisions and NSW variations apply.

Fire-fighting equipment

Hydrants

Hydrants support fire-brigade operations. Design can involve coverage, flow and pressure, boosters, pumps, tanks and brigade access. Read our fire hydrant and booster guide.

Hose reels and extinguishers

Hose reels and portable extinguishers support initial occupant response for defined risks. Their type, position and coverage must suit the building, hazards and code requirements.

Sprinklers and suppression

Sprinklers can control fire growth and may affect other parts of the fire strategy. The design basis depends on the applicable standard, occupancy and hazard. High-piled or combustible storage needs particular attention. See sprinkler system design under AS 2118.

Detection, warning and emergency communication

Smoke and heat detection, fire indicator panels, occupant warning and emergency warning/intercom systems are not interchangeable terms. Required systems depend on classification, scale and occupant risk. They also interface with sprinklers, lifts, doors, smoke-control fans and mechanical shutdown.

Our fire alarms, detection and EWIS guide explains those distinctions.

Smoke hazard management

Smoke control can include zone smoke control, stair or lift pressurisation, smoke exhaust, air-handling shutdown and other mechanical strategies. The control logic must align with detection and warning systems, power supplies and the fire strategy.

Read stair pressurisation and smoke control for the design balance and commissioning interfaces.

Emergency visibility and egress

Emergency lighting and exit signs support evacuation when normal lighting fails. Exit numbers, widths, separation and travel paths are architectural and fire-strategy matters that must be coordinated with the lighting layout.

See emergency and exit lighting to AS 2293.

Passive fire and compartmentation

Fire-resisting walls, floors, shafts, fire doors and protected service penetrations limit fire and smoke spread. Building-services routes can compromise that strategy if penetrations and dampers are not designed and recorded correctly.

Fit-outs should begin with a compartment plan. Read fire doors and compartmentation for fit-outs.

Plan the interfaces

A coordinated matrix should show each system’s power supply, monitoring, control inputs and outputs, required plant space, access, drainage, structure and commissioning responsibility. This is where a multi-disciplinary team adds value: clashes are removed before they become site variations.

Connect technical compliance to CDC eligibility

Meeting the NCC does not by itself make a project eligible for complying development. The land and proposal must also satisfy the relevant planning standards. Start with the NSW CDC eligibility checklist.

NEPA coordinates fire, hydraulic, mechanical and electrical design for eligible Fire CDC projects. Contact us during concept design to define the system and information scope.

Common questions

Frequently asked questions

Does every Class 2–9 building need hydrants and sprinklers?

No. System triggers vary with classification, size, height, construction and use. The applicable NCC provisions and NSW requirements must be assessed for the specific project.

What fire drawings are commonly needed for a CDC?

Depending on the project, drawings may cover hydrants, hose reels, sprinklers, detection and alarms, warning systems, smoke control, emergency lighting, passive fire and fire-brigade information.

Can one building have several fire-system standards?

A building can contain different classifications, existing and new systems, and Performance Solutions. The approved documents and fire safety schedule should state the applicable basis clearly for each measure.

When should fire services be designed?

Start during concept design, before plant rooms, risers, ceiling zones, exits and site access are fixed. Early coordination reduces redesign and certification risk.

Official sources

This article provides general information for NSW projects. Planning, certification and fire-safety requirements depend on the site, building classification, proposed use, scope and applicable law. Confirm the requirements for your project with the registered certifier, council and appropriately qualified practitioners.

← Fire CDC guides

Get in touch

Need a clear Fire CDC pathway?

Tell us about the building, proposed use and approval stage. We’ll help identify the fire-services design and documentation your project needs.

Discuss your project↗